Transient and permanent overvoltage protector plus undervoltage IGA 2x20A automatic reset Vigivolt Tuscan Adajusa
Transient and permanent overvoltage protector plus undervoltage IGA 2x20A automatic reset Vigivolt Tuscan Adajusa

Protector single-phase transient surges TYPE 2 and permanent + IGA 2x20A automatic rearmament COMBI-PRO-2P20T15 - Toscano

€190.96 Tax included

€157.82 tax excl.

Transient surge protector TYPE 2 and permanent plus subvoltage with automatic rearmament, with built-in IGA 2x20A pre-cabled for single-phase installations.

Protector of permanent surges caused by increases in network voltage, and transient surges caused by lightning strikes or network switches, in single-phase installations. The equipment will automatically reconnect when the mains voltage is restored within the established limits. breaking capacity of the IGA 6kA, maximum discharge intensity 15kA.

Reference: COMBI-PRO-2P20T15




Toscano_version 1 color sin leyenda
Representative image for illustrative purposes, the item supplied will correspond to the specifications indicated.

No queries yet, leave the first!
 

Combined protection assembly against transient (ground discharger) and permanent surges, associated with a 2-pole cutting device (IGA) with a breaking capacity of 6kA according to IEC-EN 63052, curve "C". It allows the reconnection of the new smart meters according to scheme 2 of the ITC-BT-52 standard.

In case of overcurrent shooting, short circuit or manual disconnection, the equipment will not rearm automatically.

Overvoltage: When the voltage exceeds 270V the equipment fires the IGA. The time it takes to fire will depend on the level of overvoltage detected (according to specifications of the UNE-EN50550 Standard). When the voltage drops below 255V and is maintained for at least 10 seconds, the equipment will reassemble the IGA by reconnecting the voltage in the mains.

Subvoltage: If the voltage drops below 180V for more than 10 seconds, the equipment fires the IGA leaving the installation without supply. When the voltage stabilizes again above 210V for more than 10 seconds, the equipment will rearm the IGA automatically.

In the event of a transient surge, the equipment absorbs it by grounding it, thus preventing it from causing any damage to the devices connected to the network. If, due to a transient surge, the protection becomes inoperative, the equipment will display the warning window in red. In this case, the protective module will have been rendered useless, and must be replaced by another, plug-in and easy to replace.

The module includes:

  • IGA 2x20A automatic reconnection
  • Permanent surge and undervoltage protector
  • Transient surge protector (ground discharger)


The whole assembly is supplied fully assembled and pre-wired.


General characteristics:

  • Manufacturer: Toscano
  • Reference: COMBI-PRO-2P20T15
  • Rated working voltage: 230VAC
  • Frequency: 50-60 Hz
  • Maximum terminal section: 25 mm
  • Protection: IP20
  • Assembly: Rail DIN
  • Number of DIN modules: 5
  • Standards: UNE-EN 60898 / UNE-EN 50550


Overvoltage:

  • Trigger voltage: >270VAC ± 2%
  • Overvoltage response time: according to UNE-EN 50550
  • Reset time: 10 seconds
  • Reconnection voltage:


Undervoltage:

  • Trigger voltage:
  • Response time per subvoltage: 10 seconds
  • Reset time: 10 seconds
  • Reconnection voltage: > 210VAC ± 2%


IGA:

  • Rated current: 20A
  • Curve: C
  • breaking capacity: 6kA


Transitory:

  • Maximum voltage Uc: 320VAC (L/N)
  • Protection level Up (L/N):
  • Protection level Up (N/PE):
  • Maximum discharge current (8/20μs) Imax (L/N): 15kA
  • Nominal discharge current (8/20μs) In (L/N): 8kA
  • Maximum discharge current (8/20μs) Imax (N/PE): 15kA
  • Nominal discharge current (8/20μs) In (N/PE): 10kA
  • Pre-protection fuse: 63A gL
  • Type: 2
  • Standards: IEC 61643-11/ EN 61643-11


For the correct operation of the equipment it is necessary to connect the terminal block "REMOTE" with the phase of the electrical installation. Also the phase must be connected in the terminal block "L" and the neutral in the terminal block "N".




To expand the information you can download the technical sheet by clicking on the "Attachments" tab.
Material for professional use, install in compliance with the regulations in force at the place of installation.

Questions

Be the first to ask a question about this product!

Question about the product

* Required fields
(read)

16 other products in the same category:

Customers who bought this product also bought:

Reviews
Product added to wishlist
Product added to compare.